Commercial Motor Operators

LIFTMASTER (POPULAR COMMCIAL OPERATORS)

Including:
COMMERCIAL ACCESSORIES
COMMERCIAL REPLACEMENT PARTS
COMMERCIAL OPTIONAL FEATURES
LIFTMASTER COMMERCIAL OPERATORS

LIFTMASTER H OPERATOR
LOGIC 4.0 TECHNOLOGY (L4)
PRINTABLE SPEC SHEET(PDF FILE) 
Added Value

• Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
• Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-RPEN4, CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
• Thermal motor overload can be easily reset from the 3-button floor level control station

Reliability & Programming Simplicity

• Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators
• All high-voltage connections have been removed from the board for safety and ease of service
• Diagnostic LEDs speed installation and troubleshooting
• Motor direction jumper lets you change motor direction by simply moving a jumper

Mechanical Reversing Contactor Circuit (M):
(115V, 208/230V, 460V, 575V, 24V NEC Class 2 Circuit with 40VA transformer) Industrial linear contactor provides significantly longer control runs than conventional contactors.

STANDARD FEATURES
Motor: Continuous-duty high-starting torque motor with instant reverse and overload protection.  Available in 1/3, 1/2, 3/4 and 1 HP; single- or three-phase. Removable without affecting limit switch settings.

Drive Reduction: First-stage heavy-duty 5L V-belt; second and third stages #48 chain; #50 drive chain.

Emergency Disconnect: Easy emergency manual operation using an electrically interlocked floor level disconnect and hoist mechanism.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close; D1 and E2 wiring are also available. Momentary contact to close (B2 wiring), T, TS, and FSTS wiring can be activated with the use of CPS-RPEN4, CPS-U, CPS-UN4, or CPS-EI safety edge interface. The operator is pre-wired to accept a sensing device, photoelectric sensors, radio controls and most types of access control equipment.

External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.

Bearings: Industrial ball bearings on a 1" output shaft; heavy-duty oil-filled iron bearings on reduction shafts.

Friction Clutch: Adjustable, helps protect against major damage to door and operator should the door meet an obstruction.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.

Push Button Station: 2-button station for OPEN/CLOSE functions is standard with D or D1 wiring.  3-button station is standard with B2 or C2 wiring.

PosiLock® Mechanical Brake System: Self-locking mechanical reduction system that functions as a holding brake.

Warranty: 1-year warranty.

CONTROL ACCESSORIES
Primary Monitored Entrapment Protection: The presence of primary entrapment protection is required for all modes and features beyond basic constant-pressure-to-close performance. Primary entrapment protection devices are monitored continuously to insure safe operation of the door and limit door operator functionality should an obstruction be detected or in the event of device failure. LiftMaster Monitored Entrapment Protection devices, CPS-RPEN4, CPS-U, CPS-UN4 and CPS-EI, are designed to work in conjunction with LiftMaster commercial door operators to provide enhanced door safety and a broad range of modes and features to end users. Either monitored photo-sensor or monitored 4-wire sensing edge (in conjunction with the CPS-EI Edge Interface) protection may be selected, but one must be detected by the LiftMaster Logic 4.0 or Medium-Duty Logic circuit board in order to unlock full functionality.

LIFTMASTER GH OPERATOR
LOGIC 4.0 TECHNOLOGY (L4)
PRINTABLE SPEC SHEET(PDF FILE)
Added Value

• Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
• Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-RPEN4, CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
• Thermal motor overload can be easily reset from the 3-button floor level control station

Reliability & Programming Simplicity

• Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators
• All high-voltage connections have been removed from the board for safety and ease of service
• Diagnostic LEDs speed installation and troubleshooting
• Motor direction jumper lets you change motor direction by simply moving a jumper

Mechanical Reversing Contactor Circuit (M):
(115V, 208/230V, 460V, 575V, 24V NEC Class 2 Circuit with 40VA transformer) Industrial linear contactor provides significantly longer control runs than conventional contactors.

STANDARD FEATURES
Motor: Continuous-duty high-starting torque motor with instant reverse and overload protection. Available in 1/2 to 5 HP; single- or three-phase. Removable without affecting limit switch settings.

Auxiliary Chain Hoist: Reduced drive chain hoist with electrically interlocked floor level disconnect for manual operation. Hoist wheel is easily moved to right- or left-hand side of unit, eliminating the need to order left- or right-hand mounting.

Drive Reduction: 45:1 using heavy-duty gears running in oil bath. Cast iron housing. Special "all-climate" synthetic gear oil for greater low-temperature performance.

Emergency Disconnect: Spring-loaded for emergency manual operation.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close; D1 and E2 wiring are also available. Momentary contact to close (B2 wiring), T, TS, and FSTS wiring can be activated with the use of CPS-RPEN4, CPS-U, CPS-UN4, or CPS-EI safety edge interface. The operator is pre-wired to accept a sensing device, photoelectric sensors, radio controls and most types of access control equipment.

External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.

Bearings: Sealed roller bearings in gear reducer.

Brake: Solenoid-actuated brake is standard to prevent coasting of door.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.

Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.

Warranty: 1-year warranty.

CONTROL ACCESSORIES
Primary Monitored Entrapment Protection: The presence of primary entrapment protection is required for all modes and features beyond basic constant-pressure-to-close performance. Primary entrapment protection devices are monitored continuously to insure safe operation of the door and limit door operator functionality should an obstruction be detected or in the event of device failure. LiftMaster Monitored Entrapment Protection devices, CPS-RPEN4, CPS-U, CPS-UN4 and CPS-EI, are designed to work in conjunction with LiftMaster commercial door operators to provide enhanced door safety and a broad range of modes and features to end users. Either monitored photo-sensor or monitored 4-wire sensing edge (in conjunction with the CPS-EI Edge Interface) protection may be selected, but one must be detected by the LiftMaster Logic 4.0 or Medium-Duty Logic circuit board in order to unlock full functionality.

LIFTMASTER T OPERATOR
LOGIC 4.O TECHNOLOGY (L4)
PRINTABLE SPEC SHEET(PDF FILE)
Added Value

• Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
• Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
• Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-RPEN4, CPS-U, CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
• Thermal motor overload can be easily reset from the 3-button floor level control station

Reliability & Programming Simplicity

• Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators
• All high-voltage connections have been removed from the board for safety and ease of service
• Diagnostic LEDs speed installation and troubleshooting
• Motor direction jumper lets you change motor direction by simply moving a jumper

STANDARD FEATURES

Motor: Continuous-duty high-starting torque motor with instant reverse and overload protection.  Available in 1/3, 1/2, 3/4 and 1 HP; single- or three-phase. Removable without affecting limit switch settings.

Drive Reduction: First-stage heavy-duty 5L V-belt; second-stage #41 chain; output on trolley #48 chain on 1/3 and 1/2 HP; #41 chain on 3/4 and 1 HP.

Emergency Disconnect: Spring-loaded for emergency manual operation.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close; D1 and E2 wiring are also available. Momentary contact to close (B2 wiring), T, TS, and FSTS wiring can be activated with the use of CPS-RPEN4, CPS-RPEN4, CPS-U, CPS-UN4, or CPS-EI safety edge interface. Operators are pre-wired to accept a sensing edge, photoelectric sensors, radio controls and most types of access control equipment.

External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.

Bearings: Ball bearings on output shaft; heavy-duty, oil-filled bushings on reduction shafts.

Brake: Solenoid-actuated brake is standard on 3/4 and 1 HP units to prevent coasting of door. Optional on 1/3 and 1/2 HP units.

Friction Clutch: Adjustable, helps protect against major damage to door and operator should the door meet an obstruction.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.

Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.

Quick-Mount Header Bracket: For fast, swing-up mounting.

Rail Assembly: High-strength dual L-rail track with nylon quiet-gliding chain guides on rail spacers for quiet, smooth operation.

Warranty: 1-year warranty.

CONTROL ACCESSORIES
Primary Monitored Entrapment Protection: The presence of primary entrapment protection is required for all modes and features beyond basic constant-pressure-to-close performance. Primary entrapment protection devices are monitored continuously to insure safe operation of the door and limit door operator functionality should an obstruction be detected or in the event of device failure. LiftMaster Monitored Entrapment Protection devices, CPS-RPEN4, CPS-U, CPS-UN4 and CPS-EI, are designed to work in conjunction with LiftMaster commercial door operators to provide enhanced door safety and a broad range of modes and features to end users. Either monitored photo-sensor or monitored 4-wire sensing edge (in conjunction with the CPS-EI Edge Interface) protection may be selected, but one must be detected by the LiftMaster Logic 4.0 or Medium-Duty Logic circuit board in order to unlock full functionality.

LIFTMASTER SL3000UL OPERATOR
PRINTABLE SPEC SHEET(PDF FILE)

The SL3000UL™ models of slide gate operators are the first choice for heavy-traffic applications and high-demand customers, including large development and management companies, prestigious residential gated communities, and custom home builders.

The Security+ 2.0™ technology used exclusively in LiftMaster® remote controls virtually eliminates interference and provides up to double the range of standard remotes so you don't have to wait at the gate to access your property.

Featuring the highest quality components and backed by years of proven reliability, each unit is carefully inspected and mechanically tested to provide unsurpassed performance. Unique engineering innovations ensure than any SL3000UL  model will meet the needs of almost every type of high-traffic gated entrance. All backed by the safety and reliability of the most advanced control board in the industry.

• 120V AC power
• 24V DC board
• Built-in model 850LM Security+ 2.0™ Receiver
• Highly efficient, extremely quiet
• Surge/lightning protection
• Alarm reset button
• Plug-in loop detectors
• Reversing sensor
• Limit switch design
• Modular OmniControl™ Board
• Wormgear reducer
• Manual disconnect
• Weatherproof high-density polyethylene cover
• Gold zinc-plated chassis eliminates corrosion
• High-speed precision limit switches
• Solid steel, machined pulley
• #41 chain

The SL3000UL gate operator is available in the following models:

• SL3000UL: standard model
• SL3000ULDC: equipped with battery backup
• SL3000ULDM: dual motor for heavier traffic and higher temperatures
• SL3000ULE: capable of manual backdrive for emergency access
• SL3000UL1HP: heavy-duty, 1 horsepower model for heavier gates

LIFTMASTER CSW24V OPERATOR
PRINTABLE SPEC SHEET(PDF FILE)

The LiftMaster® Elite Series® model CSW24V is engineered for a million cycles in high-cycle, heavy-duty applications. A Battery Backup System provides uninterrupted access when the power is out, and Security+ 2.0™ technology virtually eliminates radio interference. It also features integrated MyQ® technology and the industry's only standard wireless dual gate communication system. The CSW24V is rated for gates 18 ft. long or 1,200 lbs.

Battery Backup System provides uninterrupted access when the power is out
Provides up to 7 days or 100 cycles on battery backup. Also powers safety and ancillary devices.

Provides 2x the range of standard remote controls
Our patented Security+ 2.0™ Technology provides two times the range of standard remote controls and virtually eliminates radio interference. An on-board radio receiver is included with the CSW24V. It holds up to 50 remotes and is compatible with HomeLink® version 4 and higher.

Wireless dual gate communication prevents driveway scars and expensive wiring
The on-board radio receiver provides a single remote control solution for gates and additional access points. It also features the industry's only standard wireless dual gate communication system that saves installation time and cost and eliminates unsightly scars from cutting driveways to run conduit for primary/secondary communication wiring.

Standard Features:

• Power Management System
  Supplies power when needed to operate the gate and conserves power when not in use
  Provides exceptional standby time and cycles on battery backup
  7 days of standby time or 100 cycles on battery backup
• Fire department compliant: selectable settings allow gate to auto-open upon loss of AC power or battery depletion
• Advanced traffic management control includes Quick-close and Anti-tailgating functions
• Bi-part delay: choose from Standard Operation or Synchronized Close
• Simple-to-set electronic limit system maintains accurate gate position throughout gate travel
• High-density, UV-resistant polycarbonate two-piece cover for excellent heat and corrosion resistance
• Programmable auxiliary relays
• Plug-in loop detectors
• External obstruction sensing; complies with UL325 safety codes

Specifications:

• 24VDC continuous-duty motor with soft start/stop
• Operator duty rating: continuous
• Power: 110V or 220V Single Phase
• Surge/spike protection
• Gate travel speed: 90-degree opening in 13-15 seconds
• Constructed with 1/4" gold zinc-plated steel for rust prevention
• Weight: 206 lbs.